38mm x 0.4mm Un-Glued / Pre-Glued (Iron-on) Melamine Edging Surteco


for just 4 payments of $0

This product is currently out of stock and unavailable.

SKU: N/A Categories: , , , , ,
   

Description

38mm x 0.4mm Un-Glued / Pre-Glued (Iron-on) Melamine Edging Surteco, Manufactured in Australia

High Quality Edging for application directly onto wooden substrates such as particleboard, MDF (fibreboard) and plywood – Suitable for Pre-Glued Edgebanders or Manual Edgebanding using Virutex AG98R or Iron or other traditional means.

We have the largest range of stocked Edging in Australia supplied by quality manufacturers. We offer Edging Solutions for all users (DIY, Hobbyists, Micro Trade Users through to High Industrial Cabinetry / Furniture makers). We offer Cutting and Pre-Gluing facilities for all of our edging in addition to all the stocked lines – please refer to our Edging Services for more details.

Please note we have a larger range of Melamine Products in 0.4mm, 1mm and 2mm Thickness and larger Roll Sizes.

Suggested Applications:-

• Shelving
• Stereo speaker boxes
• Hobby craft
• Cabinets & cupboard doors
• Renovation of old furniture
Un-Glued Edging:-
You can use the following adhesives for small-batch edging if you do not have a Pre-Glued Hot Melt Edgebander:-

Pre-Glued Edging:-

How it works…
Iron-on Edging is coated on the back with a special hot melt adhesive. With heat from an ordinary domestic iron, the adhesive is melted to form a bond with the surface of the substrate.

 Fleeced Veneers
Iron-on Veneer Edging

Note – Iron-on Edging is not recommended for application onto metal, glass, or other sealed surfaces.What else will you need?A stiff-bristled brush; Brown or grease proof paper (not vital); A hard roller or flat wooden block (palm-sized); A router, fine file, chisel, or utility knife; Fine sandpaper; Timber stain/lacquer.If applying Iron-On Melamine Edging to laminate or painted surface: Coarse sandpaper and/or paint stripper.Preparation:-1. Substrate Surface – Remove laminate or paint using coarse sandpaper and/or paint stripper. Clean-up substrate surface using stiff-bristled brush.

2. Iron-on Timber Veneer Edging – Measure and cut edging allowing 10mm overlap on each end.

3. Domestic Iron – Turn off steam function. Set iron to high heat (cotton setting).

Method:-

1. Position Edging – Lay edging over substrate allowing equal overlap ona ll sides for trimming.

2. Cover Edging (not vital) – Cover edging strip with brown or grease proof paper to protect surface of edging from excessive direct heat from iron. (see illustration A)

3. Iron-on – Use on hand to guide and keep edging in position. Starting at one end, iron back and forth. Slowly continue forwards. (see illustration A)

4. Follow-up Pressure – Rub wooden block or push roller back and forth immediately after ironing (whilst edging and adhesive still warm) to keep edging in contact with substrate surface as adhesive cools. (see illustration B)

Note – If result is not acceptable, re-work by repeating steps 3 and 4.

5. Trimming – Ideally use a router. Alternatively: With fine file – Move file at close angle (15º) to surface of board. With chisel or utility knife – Work along surface of substrate. Trim carefully to avoid damaging surface of substrate. In all cases, work away from edging towards surface of substrate to stop edging pulling away. Alternatively use Virutex AU93 Edge Trimmer and RC21E End Trimmers.

6. Finishing – If required, fine sandpaper trimmed edges to smooth finish.

Please note – The above instructions and information are given in good faith and are based on our testing and experience. All recommendations and suggestions are made without a guarantee of any kind as strict adherence to application instructions, substrate quality and working conditions are beyond our control.

Additional information

Brand
Solid Colour Black Stipple, White Satin, White Stipple, Antique White
Width 21mm, 38mm
Pre-Glued / Un-Glued Pre-Glued, Un-Glued
Cutting Fee 50M, 100M, Cut Surcharge

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.